Marca: Samsung
Modelo: HD502HJ
Fecha de Fabricación: 2011.06
Número de Serie: S20BJ90B676085
Lugar de Fabricación: China
Factor de Forma: HDD 3.5"
Conexión: SATA
Capacidad: 500
Estado del Disco: Usado pero OK
PCB Nº BF41-00352A 00
PCB Sticker: F3_1D REV.01 R00
MCU: 88i9025-TFJ2
De Frente De Dorso Del PCB
De Dorso Del PCB
Del PCB
S.M.A.R.T & Informe P/N: A7783-C721-A6NER Model : HD502HJ HDD P/N : HD502HJ LBA 976.773.168 500.0GB location: /dev/disk2 partition count: 1 partitions: Reservado para el sistema, SMART Support: Supported Last SMART Error: *not set* Model Family: SAMSUNG SpinPoint F3 Model: SAMSUNG HD502HJ Serial Number: S20BJ90B676085 Firmware Version: 1AJ10001 Capacity: 500 GB ATA Version: 8 SATA Version: SATA 2.6, 3.0 Gb/s Rotation Rate: 7200 rpm Health: Passed Overall Health: PASSED Offline Data Status: 0 Self Test Status: 0 Offline Data Collection Time: 4740 Data Collection Capabilities: 5B SMART Capabilities: 3 Error Logging Capabilities: 1 Short Self Test Time: 2 Long Self Test Time: 79 Conveyance Self Test Time: 0 Attribute Log Revision: 16 Attribute Count: 22 Attributes: ID# ATTRIBUTE NAME FLAG VALUE WORST THRESH TYPE UPDATED FAILED RAW VALUE 1 Raw Read Error Rate 0x002F 100 100 051 Pre-fail Always Never 0 2 Throughput Performance 0x0026 252 252 000 Old age Always Never 0 3 Spin Up Time 0x0023 083 082 025 Pre-fail Always Never 5424 4 Start/Stop Count 0x0032 100 100 000 Old age Always Never 141 5 Reallocated Sector Count 0x0033 252 252 010 Pre-fail Always Never 0 7 Seek Error Rate 0x002E 252 252 051 Old age Always Never 0 8 Seek Time Performance 0x0024 252 252 015 Old age Offline Never 0 9 Power On Hours 0x0032 100 100 000 Old age Always Never 2210 10 Spin Retry Count 0x0032 252 252 051 Old age Always Never 0 11 Calibration Retry Count 0x0032 252 252 000 Old age Always Never 0 12 Power Cycle Count 0x0032 100 100 000 Old age Always Never 147 191 G-Sense Error Rate 0x0022 100 100 000 Old age Always Never 1 192 Power Off Retract Count 0x0022 252 252 000 Old age Always Never 0 194 Temperature Celsius 0x0002 064 063 000 Old age Always Never 24 195 Hardware ECC Recovered 0x003A 100 100 000 Old age Always Never 0 196 Reallocated Event Count 0x0032 252 252 000 Old age Always Never 0 197 Current Pending Sector Count 0x0032 252 252 000 Old age Always Never 0 198 Offline Uncorrectable Sector Count 0x0030 252 252 000 Old age Offline Never 0 199 UDMA CRC Error Count 0x0036 098 001 000 Old age Always Never 1565 200 Multi Zone Error Rate 0x002A 100 100 000 Old age Always Never 372 223 Load Retry Count 0x0032 252 252 000 Old age Always Never 0 225 Load Cycle Count 0x0032 100 100 000 Old age Always Never 150 Error Log Version: 1 Error Count: 8 Error Log: Error 8 occured at disk power-on lifetime: 2201 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 01 00 00 A0 Error: Interface CRC error, Interface CRC error with 1 sectors at LBA = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- C8 20 01 01 00 00 A0 00 00:00:00.573 READ DMA EF 03 45 00 4F C2 A0 00 00:00:00.573 SET FEATURES [Set transfer mode] EF 03 0C 00 4F C2 A0 00 00:00:00.573 SET FEATURES [Set transfer mode] C6 DA 10 00 4F C2 A0 00 00:00:00.573 SET MULTIPLE MODE B0 DA 00 00 4F C2 A0 00 00:00:00.573 SMART RETURN STATUS Error 7 occured at disk power-on lifetime: 2161 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 A0 Error: Unknown Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- EC 00 00 00 00 00 A0 08 00:00:11.559 IDENTIFY DEVICE 00 00 01 01 00 00 00 08 00:00:11.558 NOP [Abort queued commands] EC 00 00 00 00 00 A0 08 00:00:11.553 IDENTIFY DEVICE 00 00 01 01 00 00 00 08 00:00:11.553 NOP [Abort queued commands] EC 00 00 00 00 00 A0 08 00:00:11.548 IDENTIFY DEVICE Error 6 occured at disk power-on lifetime: 2161 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 08 00 00 00 E0 Error: Interface CRC error, Interface CRC error with 8 sectors at LBA = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- C8 00 08 00 00 00 E0 08 00:00:11.548 READ DMA 27 00 00 00 00 00 E0 08 00:00:11.548 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] EC 00 00 00 00 00 A0 08 00:00:11.548 IDENTIFY DEVICE EF 03 46 00 00 00 A0 08 00:00:11.548 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 E0 08 00:00:11.548 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 5 occured at disk power-on lifetime: 2158 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 01 00 00 A0 Error: Interface CRC error, Interface CRC error with 1 sectors at LBA = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- C8 20 01 01 00 00 A0 00 00:00:00.177 READ DMA EF 03 45 00 4F C2 A0 00 00:00:00.177 SET FEATURES [Set transfer mode] EF 03 0C 00 4F C2 A0 00 00:00:00.177 SET FEATURES [Set transfer mode] C6 DA 10 00 4F C2 A0 00 00:00:00.177 SET MULTIPLE MODE B0 DA 00 00 4F C2 A0 00 00:00:00.177 SMART RETURN STATUS Error 4 occured at disk power-on lifetime: 2157 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 01 00 00 A0 Error: Interface CRC error, Interface CRC error with 1 sectors at LBA = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- C8 20 01 01 00 00 A0 00 00:00:00.046 READ DMA EF 03 45 00 4F C2 A0 00 00:00:00.046 SET FEATURES [Set transfer mode] EF 03 0C 00 4F C2 A0 00 00:00:00.046 SET FEATURES [Set transfer mode] EF 03 0C 00 4F C2 A0 00 00:00:00.046 SET FEATURES [Set transfer mode] C6 DA 10 00 4F C2 A0 00 00:00:00.046 SET MULTIPLE MODE Self Test Log Revision: 1 Self Test Log Count: 0 Self Test Log: No self tests logged.
Cargado Por: Franco 1